cnc milling surface finish standards
When CNC machining aluminum alloys and stainless steel, surface roughness is typically controlled within a range of Ra 0.8 to 3.2 micrometers. We must adjust the CNC feed rate and use a roughness tester to verify compliance with surface roughness requirements in order to achieve high-quality surface finish standards.
The Impact of Surface Roughness on Component Fatigue Life
Surface roughness has a significant impact on the fatigue life of mechanical components. The valleys formed by the cutting tool can trigger crack propagation under mechanical stress. Reducing the surface finish of a metal structural component from Ra 3.2 μm to Ra 0.8 μm can increase the fatigue limit of the metal material by 14% to 18%. For the sealing surfaces of sealing components, maintaining a surface finish of Ra 0.4 μm prevents O-rings from experiencing compression deformation and side leakage under operating pressures exceeding 300 bar.

Machining Parameter Control for Achieving Milling Finishes from Ra 0.4 μm to 3.2 μm
Metal surface roughness is directly related to the spindle speed (n), feed per tooth (f_z), and the shape of the tool's cutting edge during the machining process. Strict control of these parameters is essential to prevent chatter marks and dimensional deviations during machining.
Relationship between feed rate (f_z) and step size: The theoretical surface roughness (Ra) is proportional to the square of the feed per tooth. In multi-axis machining, using a 4-flute ball-nose end mill with a step size controlled at 0.1 mm can achieve an Ra of 0.8 μm.
Optimization of the cutting edge geometry: When machining ductile materials such as AL6061-T6, using a solid carbide end mill with a polished chip flute reduces material adhesion and the formation of built-up edges. The use of finishing inserts on face mills flattens microscopic irregularities in the tool path, reducing the measured Ra value by 50% without reducing the feed rate.
Coolant pressure parameters: A high-pressure, 70 bar, center-spindle water-cooling system immediately forces chips out of the machining zone, preventing surface scratches and abnormal fluctuations in Ra values during deep pocket milling.
To strictly control these parameters during mass production, please clearly specify your surface finish grade and dimensional tolerance requirements.

cNC machining service in China
Please submit the STEP file containing the Ra requirements and the 2D engineering drawings directly to us. Request a CNC Machining Quote now to initiate a DFM (Design for Manufacturability) analysis.
Comparison of machining processes and achievable Ra values. The table below lists the average surface roughness ranges based on specific milling parameters.
| Machining Process | Achievable Surface Finish (Ra) | Typical Material Application | Tolerance Capability (ISO 2768-f) |
| Heavy Rough Milling | 6.3μm - 12.5μm | Cast Iron, Carbon Steel | ±0.15mm |
| Standard Contour Milling | 1.6μm - 3.2μm | AL6063-T5, SUS304 | ±0.05mm |
| High-Speed Finishing | 0.8μm - 1.6μm | AL7075-T6, Titanium Grade 5 | ±0.02mm |
| Wiper Insert Face Milling | 0.4μm - 0.8μm | Aluminum Alloys, Brass | ±0.01mm |
The impact of post-processing on final surface quality
Mechanical and chemical secondary processing systematically alter the initial milled surface roughness. The QA quality control process must account for these dimensional and textural deviations prior to final inspection. Glass Bead Blasting: Spraying 120-mesh glass beads at a pressure of 60 PSI produces an isotropic matte finish. This process roughens the machined surface from Ra 1.6 μm to approximately Ra 2.0 μm while masking residual tool marks. Electropolishing (ASTM B912): Removes 5 μm to 10 μm of material from the SUS316L surface, dissolving microscopic peaks. This process reduces the Ra 0.8 μm of the reference milling to Ra 0.2 μm, directly improving chemical corrosion resistance. Hard anodizing (MIL-A-8625 Type III): Generates a 50 μm aluminum oxide layer on the AL6063 surface. The growth of anodic crystals increases the base roughness by 10% to 15%; therefore, to achieve the post-anodizing target of Ra 0.8 μm, the machining finish prior to anodizing must meet a mandatory requirement of Ra 0.6 μm.

FAQ: Verification of CNC Milling Surface Finish Ra 0.8 μm
What is the standard CMM inspection protocol for surface finish?
We use a contact profilometer with a probe radius of 2 μm and a cutoff wavelength (Lc) set to 0.8 mm. Inspections strictly follow ISO 4287 guidelines, with five consecutive sample lengths taken from the machined surface to calculate the average Ra value.
What are the differences in surface finish performance between AL6063-T5 and SUS304 under standard milling conditions?
AL6063-T5 exhibits lower cutting forces; using a carbide end mill at a cutting speed of 800 m/min, a stable Ra value of 0.8 μm can be achieved. SUS304 tends to cause rapid tool wear and built-up edge; under the same conditions, without specialized high-pressure coolant and TiAlN-coated inserts, it typically yields only an Ra of 1.6 μm.
Does secondary hard anodizing affect the dimensional tolerances of parts with a Ra of 0.8 μm?
Yes. The hard anodized layer grows outward by 50%. A 50 μm coating increases the thickness on one side by 25 μm, resulting in a 50 μm reduction in the inner bore diameter. This chemical reaction also increases the base Ra roughness by approximately 15%.






