CNC Turning Service for Custom Round Parts
Shafts, sleeves, bushings, and threaded components made from customer drawings. Heron-Alu in Xiamen reviews fits, bores, shoulders, and any secondary milled features before quoting
ISO 9001:2015| IATF 16949:2016| SGS |ROSH

Turned Parts Built Around the Features That Matter
A diameter may locate a bearing while a shoulder sets its position. Our review starts with those working surfaces.
Outside diameters and faces
Mark working fits and faces that set installed position.
Bores
Bores: Identify through or blind form, useful depth and mating fit.
Threads and grooves
Give thread form, usable length, and groove purpose.
Shafts, sleeves and bushings
Similar outlines can need different holding and checks.
Slender parts
Show the full length and surfaces that a support cannot touch.
Secondary milling
Locate flats, slots or cross holes from the turned datum.
Material and finish
Specify grade, condition, treatment and masked areas.
Inspection
Name the fits, runout and positions that govern acceptance.
Request CNC Turning Quote
Custom CNC Turning for Prototype and Repeat Components
Heron-Alu's CNC turning service covers shafts, sleeves, bushings, and other parts built around a centerline. Fits between diameters, bores, and shoulders often matter more than the overall outline. Flats and cross holes may add another setup. Before ordering, identify the material grade, drawing revision, quantity, finish and inspection records needed at delivery. A worn sample may not preserve its original fit, so a replacement needs extra measurement. The Heron-Alu catalog shows turned parts, plastic turning, and parts with both turned and milled features. The Xiamen team reviews customer drawings or samples and quotes the complete component.
Explore CNC Turned Part Types
These current catalog groups show part types; the drawing and quotation define each order.

CNC Turned Parts
Steps, shoulders and grooves locate mating parts. A shoulder may seat a bearing while a groove retains the assembly. Mark the working fits and finish applied after turning.

CNC Turning Milling
A round part may need flats, a radial hole or a slot. Locate these from the turned axis. Include both setups and their shared datum in the quote.

Plastic CNC Turning
For plastic bushings, name the resin and specify mating dimensions, working temperature and moisture conditions. A close bore should be assessed in its intended working condition.
CNC Turning Service Specification Tabs
CNC Turning Technical Specifications
| Feature | Guideline
|
| Maximum Part Size | Ø1000 mm × 3000 mm length |
| Minimum Part Size | From Ø1 mm |
| Minimum Wall Thickness | Keep walls at 0.3 mm or thicker on metal parts |
| Internal Radii | 0.2mm at minimum. A bigger radius is always welcome; |
| Threads
|
We cut internal and external threads from M1.5. Thread length works best at 1.5× the diameter or more |
| Holes
|
Down to Ø0.3 mm. Past 10×diameter deep, drills start to wander, so try to stay under that |
| Edge Condition
|
We break sharp edges by default. If you need an exact chamfer or radius, put it on the drawing |
| Marking | If you need to print part numbers or logos on the machined parts, we can provide laser marking services. |
cNC turning Machining and Secondary Operations
|
Operation |
What the route must account for |
|
Outside turning and facing |
Steps, tapers, shoulders, chamfers and end faces. |
|
Drilling and boring |
Through or blind bores, depth and tool reach. |
|
Threading and grooving |
Relief, remaining wall and burr access. |
|
Parting and reverse-side work |
Second operation when both end faces are functional. |
|
Milling after turning |
Flats, slots or cross holes located from a turned datum. |
|
Finishing |
Coating, masking and dimensions checked after treatment. |

Materials for CNC Turning
Heron-Alu's provides precision CNC turning services for a wide range of metals and engineering plastics. We machine custom turned parts in aluminum, stainless steel, brass, copper, alloy steel, titanium, POM, PEEK, and other materials to meet your specific design, tolerance, and performance requirements.
|
Material |
Available Grades |
Applications & Typical Parts |
|---|---|---|
|
Aluminum |
6061-T6, 6082-T6, 7075-T6, 2024-T3, 5052, 6063-T6 |
Aerospace components, automotive parts, motor housings, precision shafts, spacers, and threaded fittings. |
|
Stainless Steel |
303, 304, 304L, 316, 316L, 416, 420, 17-4 PH |
Medical instrument components, food processing equipment, valve bodies, precision shafts, couplings, and corrosion-resistant fittings. |
|
Brass |
C36000, C26000, C46400 |
Electrical connectors, plumbing fittings, valve components, threaded inserts, bushings, and precision fasteners. |
|
Copper |
C10100, C11000, C14500 |
Electrical terminals, conductive contacts, power connectors, heat transfer components, and electrical bushings. |
|
Carbon Steel |
1018, 1045, 12L14, 1215 |
Automotive shafts, threaded studs, pins, sleeves, bushings, and general machinery components. |
|
Alloy Steel |
4140, 4340, 4130, 8620 |
High-strength shafts, transmission components, gear blanks, bearing sleeves, hydraulic components, and heavy-duty machine parts. |
|
Titanium |
Grade 2, Grade 5 (Ti-6Al-4V), Grade 23 |
Aerospace fasteners, medical device components, lightweight shafts, precision connectors, and corrosion-resistant components. |
|
POM (Acetal) |
POM-C, POM-H, Delrin |
Precision bushings, bearing sleeves, rollers, spacers, valve seats, and low-friction mechanical components. |
|
PEEK |
Natural PEEK, PEEK GF30, PEEK CF30 |
Aerospace components, medical device parts, high-temperature bushings, sealing rings, electrical insulators, and wear-resistant components. |
|
Nylon (PA) |
PA6, PA66, PA6-GF30, PA66-GF30 |
Plastic rollers, bushings, bearing sleeves, spacers, pulleys, and industrial machinery components. |
|
PTFE |
Virgin PTFE, Glass-Filled PTFE, Carbon-Filled PTFE |
Chemical-resistant seals, valve seats, bearing rings, insulating sleeves, and low-friction bushings. |
|
Other Plastics |
PCTFE, PPS, UHMW-PE, PVC, ABS, PC |
Insulating components, fluid-handling parts, wear-resistant sleeves, plastic spacers, and custom precision-turned parts. |
Our CNC turning service starts with the surfaces that make a round part work: a bearing seat, a bore, a shoulder or a thread. Our team can also review flats and cross holes that need a later milling setup.
Fits are discussed before price: Mark the diameter, bore and shoulder relationships that locate mating parts. We can then quote the component against the features that affect assembly.
Secondary work stays visible: A cross hole or milled flat is included in the process discussion, with its position tied to the turned datum on the drawing.
Thin-wall parts get a separate plan: For a sleeve, the holding method and final check after release matter. We review these points rather than treating a thin tube like a solid shaft.
A useful record for another order: Confirm material, revision, finish and required inspection items with the approved sample so later purchases refer to the same part definition.

Make Internal Features and Threads Unambiguous
A bore can be a clearance hole, a press fit, a sliding surface or a fluid passage. Show its useful depth, entry chamfer and bottom shape where those features affect the mating part. For a long bore, state the length over which its size or finish matters. A blind bore that merely accepts a screw needs a different review from a deep bearing bore with a working surface along its full length.
Threads need a complete callout: form, pitch, class or fit where applicable, usable length, and any lead-in or relief near a shoulder. A groove also needs width, depth and position, but its purpose is just as useful. A seal groove, oil groove and retaining-ring groove are not interchangeable. If a cross hole breaks into a bore, the drawing should address the internal burr and whether flow, sealing or sliding is affected.
Material, Stock and Support During Turning
Heron-Alu's turning catalog shows aluminum, steels, brass, titanium alloys and engineering plastics. Specify the grade and condition; a heat-treated shaft and a plastic bushing need different finishing plans. For plastics, state working temperature and moisture conditions.
Tube stock can save cutting on a sleeve, but its starting bore is not a finished fit. Solid bar may suit a closed end. For a long shaft, show its smallest diameter and any surface that a support cannot touch. For a short spacer, say whether both end faces set its finished length.
Bearing Fits and Datum Strategy
On a stepped shaft, the bearing seat's fit comes from the bearing design. The shoulder locates the bearing axially, and its corner must clear the bearing chamfer. State the usable thread length and any relief needed for the nut to seat.
The drawing should give the seat's size and fit class, shoulder distance and any runout limit from the seat's axis. Distinguish the bearing land from a clearance diameter. If the part is heat treated or coated, mark which features are checked in the final condition. The inspection record can then focus on fit, shoulder position, runout, thread and edge condition.
Project Case: Stainless Steel Thin-Wall Sleeve

Illustrative stainless steel thin-wall sleeve shown after release from a turning fixture
A CNC turning service for this stainless steel sleeve starts with its thin wall between the bore and outside diameter. The drawing needs to define the finished bore, outside diameter, wall thickness and form limits. A thin sleeve can appear correct while held and then change shape when the clamping load is removed. The inspection condition therefore matters as much as the nominal dimensions.
The proposed route uses soft jaws that support the circumference or an elastic collet rather than concentrated gripping points. Rough turning leaves even material for a finishing pass. Where access permits, the bore, outside diameter and reference end face are finished in one holding so their relationship does not depend on another setup. If the opposite face needs a second holding, the clamping plan must account for the already finished wall. The critical tradeoff is holding firmly enough to cut while avoiding pressure that changes the sleeve's shape.
Stainless steel adds another concern: a tool that rubs instead of cutting can harden the surface and leave chatter in the bore. A sharp finishing edge, a suitable nose radius, controlled depth of cut and a clear path for chips help avoid repeated rubbing. Tool condition and size trend should be checked during the run. Cooling must reach the cutting zone without trapping chips in the thin sleeve. These choices are set against the actual steel grade and wall section, rather than a single speed used for every stainless part.
The customer's technical concern is the sleeve's condition after release, when clamping pressure no longer holds it round. Consider its bore and outside diameter together with local wall thickness and form along the working length. The machining and checking plan follows those requirements:
|
Customer technical requirement |
Machining approach |
How to verify |
|
Bore and outside diameter in the free state |
Support the circumference with soft jaws or an elastic collet. Leave even stock after roughing, then finish both surfaces in one holding where access permits. |
Unclamp before checking both diameters at several axial sections and angular positions, after the part reaches a stable measurement temperature. |
|
Local wall thickness |
Keep the bore and outside diameter on a common setup and avoid gripping pressure that shifts the thin wall. |
Check thickness at specified sections and positions around the circumference. An average calculated from two diameters can hide an eccentric bore. |
|
Roundness at working sections |
Support the wall evenly during the finishing pass and avoid point loads from the fixture. |
Use a suitable form measurement method on cross-sections named on the drawing, after the sleeve is released. |
|
Cylindricity along the working length |
Review support and finishing allowance across the full length, including the area near the jaws. |
Check form over the working length in the free state against the customer's drawing. |
|
Reference end face and finished length |
Finish the bore, outside diameter and reference face in one holding when possible; plan a gentle second holding for the opposite face if needed. |
Check the end-face relationship and length from the stated datum after the final operation. |
Acceptance limits come from the customer's released drawing. The table states the proposed process and verification approach; it makes no claim about measured results.
Inspect the Relationship, Then Control the Revision
Inspection for custom turned parts should follow assembly. Diameter alone does not establish shaft runout or a cross hole's position from a bore. Define the datum, checked feature and limit on the drawing. Choose the measurement method for each feature and name working areas that need finish or burr checks.
Record what a prototype reveals about fit, then release a revised drawing for an approved change. Send Heron-Alu the model, drawing, material, quantity and finish through the contact page. The CNC turning service quote should include turning, secondary work and required inspection records.
FAQ
Q: Can I send a sample instead of a drawing for CNC turning?
A: Yes, a sample can start the discussion. Tell us whether it is new, worn or modified, and explain how it fits with other components. A physical part may not reveal its original material grade, intended tolerance or heat treatment. We will identify what must be measured and documented before a replacement can be priced for repeatable supply.
Q: Which materials are available for custom turned parts?
A: The current Heron-Alu site lists aluminum, steels, titanium alloys and engineering plastics in its CNC range. Availability of a particular grade and bar size should be checked for the order. Put the material specification and condition on the drawing. If another grade could work, describe the part's job and the properties you need before asking for a substitute.
Q: Can a CNC lathe service include flats or cross holes?
A: The site lists turning and milling products. Include all flats, slots and cross holes on the complete model and drawing. Their position relative to the turned axis may need another setup and a separate inspection step. The quotation should address the complete component rather than only its round profile. State any angular relationship that affects assembly.
Q: What tolerances can your CNC turning service achieve?
A: The answer depends on the material, diameter, length, feature, holding method, finish and way the measurement will be taken. A short outside diameter differs from a deep bore or a slender shaft. Mark the functional fits and relationships on the current drawing. We can review those specific callouts for the proposed part rather than offer one universal number.
Q: Do you quote one prototype before a repeat order?
A: The current website presents prototype work. Send the drawing and the quantity needed for the initial test. Tell us what the prototype must prove, such as a bearing fit, a seal or the location of a cross hole. A later purchase should use the approved drawing revision and state any change found during testing so that the repeat order is clear.
Q: What should I include in a turning quotation request?
A: Send a 3D model and 2D drawing when available, together with material grade, quantity, finish, delivery destination and target arrival date. Call out threads, fits, shoulders, bores and any milled features. If you need a material record or a measurement report, request it at the start. For a sample-based inquiry, describe its condition and the mating assembly.
We're professional CNC turning manufacturers and suppliers in China, specialized in providing high quality custom service. We warmly welcome you to wholesale cheap CNC turning from our factory.
Lathe Machining Services, 3d CNC Routing, CNC Turning and Milling









